EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Ultrasonic‐Enabled Nondestructive and Substrate‐Independent Liquid Metal Ink Sintering

Sanhu Liu, Zhiwu Xu, Guoqiang Li, Zhengwei Li, Zihan Ye, Zirong Xu, Wenjun Chen, Dongdong Jin, Xing Ma iD

Advanced Science · 2023-08 · 10 (23)

DOI: 10.1002/advs.202301292 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Science, online erschienen am 14.06.2023. Verfasst von Sanhu Liu und 8 weiteren Autor:innen. Beteiligte Einrichtung: State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin, 150001, China. Die Arbeit wurde bisher 64-mal zitiert (Crossref) und nennt 55 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Shenzhen Science and Technology Program, Fundamental Research Funds for the Central Universities.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Printing or patterning particle‐based liquid metal (LM) ink is a good strategy to overcome poor wettability of LM for its circuits’ preparation in flexible and printed electronics. Subsequently, a crucial step is to recover conductivity of LM circuits consisting of insulating LM micro/nano‐particles. However, most widely used mechanical sintering methods based on hard contact such as pressing, may not be able to contact the LM patterns' whole surface conformally, leading to insufficient sintering in some areas. Hard contact may also break delicate shapes of the printed patterns. Hereby, an ultrasonic‐assisted sintering strategy that can not only preserve original morphology of the LM circuits but also sinter circuits on various substrates of complex surface topography is proposed. The influencing factors of the ultrasonic sintering are investigated empirically and interpreted with theoretical understanding by simulation. LM circuits encapsulated inside soft elastomer are successfully sintered, proving feasibility in constructing stretchable or flexible electronics. By using water as energy transmission medium, remote sintering without any direct contact with substrate is achieved, which greatly protect LM circuits from mechanical damage. In virtue of such remote and non‐contact manipulation manner, the ultrasonic sintering strategy would greatly advance the fabrication and application scenarios of LM electronics.

Schlagwörter

Stichwörter der Autor:innen

circuits fabricationflexible electronicsliquid metalnon-contact sinteringultrasonic sintering

Autor:innen und Institutionen

  • State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin, 150001, China.
  • School of Materials Science and Engineering, Harbin Institute of Technology, Harbin, 150001, China.
  • Sauvage Laboratory for Smart Materials, School of Materials Science and Engineering, Harbin Institute of Technology (Shenzhen), Shenzhen, Guangdong, 518055, China.

ORCID-Profile: Xing Ma

Förderung

  • National Natural Science Foundation of China
  • Shenzhen Science and Technology Program
  • Fundamental Research Funds for the Central Universities

Zitieren

APA

Liu, S., Xu, Z., Li, G., Li, Z., Ye, Z., Xu, Z., Chen, W., Jin, D., & Ma, X. (2023). Ultrasonic‐Enabled Nondestructive and Substrate‐Independent Liquid Metal Ink Sintering. Advanced Science, 10(23). https://doi.org/10.1002/advs.202301292

Vancouver

Liu S, Xu Z, Li G, Li Z, Ye Z, Xu Z, et al. Ultrasonic‐Enabled Nondestructive and Substrate‐Independent Liquid Metal Ink Sintering. Advanced Science. 2023;10(23). doi:10.1002/advs.202301292

BibTeX
@article{Liu2023,
  author = {Liu, Sanhu and Xu, Zhiwu and Li, Guoqiang and Li, Zhengwei and Ye, Zihan and Xu, Zirong and Chen, Wenjun and Jin, Dongdong and Ma, Xing},
  title = {Ultrasonic‐Enabled Nondestructive and Substrate‐Independent Liquid Metal Ink Sintering},
  journal = {Advanced Science},
  year = {2023},
  volume = {10},
  number = {23},
  doi = {10.1002/advs.202301292}
}
Kostenlos starten →