EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Lithium All‐Solid‐State Batteries Fabricated at Room Temperature by the Powder Aerosol Deposition Method with Garnet‐Type Electrolyte and Graded Composite Cathode

Lukas Hennerici, Paula Ficht, Maximilian Schamel, Ulrich Mansfeld, Mario Linz, Daniel Paulus, Jaroslaw Kita, Michael A. Danzer, Ralf Moos

Advanced Materials Technologies · 2025-02 · 10 (3)

DOI: 10.1002/admt.202400745 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Materials Technologies, online erschienen am 23.08.2024. Verfasst von Lukas Hennerici und 8 weiteren Autor:innen. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 81 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bundesministerium für Bildung und Forschung.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Lithium‐based all‐solid‐state batteries (ASSBs) are attracting worldwide attention as the next step in the evolution of Li‐ion batteries (LIBs). They have the potential to address safety concerns and limited energy densities, which are key challenges for LIBs. The current focus is on enhancing the electrochemical properties of ASSBs. However, a suitable economic method for fabricating them remains to be established, especially when ceramic materials are used as solid electrolytes. The powder aerosol deposition method (PAD or ADM) is a ceramic processing method that uses raw ceramic powders to fabricate dense, several micrometer thick ceramic films. The entire process takes place at room temperature and in the absence of additional binders. Therefore, PAD is used in this study to fabricate ASSBs with LiNi 0.83 Mn 0.11 Co 0.06 O 2 (NMC) as the cathode active material and Al 0.2 Li 6.025 La 3 Zr 1.625 Ta 0.375 O 12 (LLZO) as the solid electrolyte. The cathode is fabricated as a composite with a gradient in the electrolyte concentration. The successful fabrication is confirmed through scanning electron microscopy and energy‐dispersive X‐ray spectroscopy analysis. Electrochemical characterization shows that a PAD‐ASSB can be cycled. Furthermore, it can be shown that 145 µm thick NMC films can be fabricated by PAD. The electrochemical results are compared with the theoretical potential of PAD‐ASSBs, and methods to further improve the achieved state are discussed.

Förderung

  • Bundesministerium für Bildung und Forschung

Zitieren

APA

Hennerici, L., Ficht, P., Schamel, M., Mansfeld, U., Linz, M., Paulus, D., Kita, J., Danzer, M. A., & Moos, R. (2025). Lithium All‐Solid‐State Batteries Fabricated at Room Temperature by the Powder Aerosol Deposition Method with Garnet‐Type Electrolyte and Graded Composite Cathode. Advanced Materials Technologies, 10(3). https://doi.org/10.1002/admt.202400745

Vancouver

Hennerici L, Ficht P, Schamel M, Mansfeld U, Linz M, Paulus D, et al. Lithium All‐Solid‐State Batteries Fabricated at Room Temperature by the Powder Aerosol Deposition Method with Garnet‐Type Electrolyte and Graded Composite Cathode. Advanced Materials Technologies. 2025;10(3). doi:10.1002/admt.202400745

BibTeX
@article{Hennerici2025,
  author = {Hennerici, Lukas and Ficht, Paula and Schamel, Maximilian and Mansfeld, Ulrich and Linz, Mario and Paulus, Daniel and Kita, Jaroslaw and Danzer, Michael A. and Moos, Ralf},
  title = {Lithium All‐Solid‐State Batteries Fabricated at Room Temperature by the Powder Aerosol Deposition Method with Garnet‐Type Electrolyte and Graded Composite Cathode},
  journal = {Advanced Materials Technologies},
  year = {2025},
  volume = {10},
  number = {3},
  doi = {10.1002/admt.202400745}
}
Kostenlos starten →