Multifunctional Conductive Nanoporous Carbon Honeycombs for Electrothermal Direct Air Capture
Advanced Materials · 14.11.2026
DOI: 10.1002/adma.75704 ↗Kurz gefasst
Fachartikel in der Zeitschrift Advanced Materials, online erschienen am 14.11.2026. Verfasst von Zekai Ji und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Engineering, National University of Singapore, Singapore, Singapore. Die Arbeit nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: National Research Foundation, Agency for Science, Technology and Research, Ministry of Education, Singapore.
Abstract (Originalsprache)
Direct air capture (DAC) requires sorbent contactors that can process large air volumes with minimal pressure drop while enabling rapid, energy‐efficient regeneration. A multiscale conductive honeycomb contactor based on nanoporous amorphous carbon (NAC) is presented, in which adsorption‐active porosity, mechanical support, electrical conduction, and Joule‐heat generation are integrated within the same continuous framework. The fully interconnected NAC pore network accommodates epoxide‐functionalized polyethyleneimine while preserving CO 2 ‐accessible transport pathways after binder‐assisted shaping into a mechanically robust monolith. Straight‐through honeycomb channels enable low‐resistance airflow with efficient CO 2 capture, whereas the conductive NAC walls act as volumetric heating elements positioned directly adjacent to the CO 2 ‐binding phase for fast regeneration. The optimized contactor achieves a volumetric adsorption productivity of up to 0.32 mmol cm −3 h −1 while maintaining a specific fan‐energy demand below 10 J m −3 . Direct Joule heating enables more than 95% desorption within 16 min under the laboratory N 2 ‐purge protocol, approximately twofold faster than external heating under the same conditions, with no measurable capacity loss over a 15‐cycle short‐term test. The key advance is the simultaneous integration of high volumetric capacity, accessible nanoporous transport, mechanical robustness, low‐resistance airflow, and electrothermal regeneration within a single honeycomb contactor.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Materials Science and Engineering, National University of Singapore, Singapore, Singapore.
- Institute for Functional Intelligent Materials, National University of Singapore, Singapore, Singapore.
- Department of Physics, National University of Singapore, Singapore, Singapore.
- Centre for Advanced 2D Materials, National University of Singapore, Singapore, Singapore.
ORCID-Profile: Sanjeevi Jayakumar, Carlos Maria Alava Limpo, Yong Kang Ong, Maxim Trubyanov, Kostya S Novoselov, Jong Hak Lee, Barbaros Özyilmaz
Förderung
- National Research Foundation
- Agency for Science, Technology and Research
- Ministry of Education, Singapore
Zitieren
APA
Ji, Z., Jayakumar, S., Limpo, C. M. A., Ong, Y. K., Madhav, A., Trubyanov, M., Novoselov, K. S., Lee, J. H., & Özyilmaz, B. (2026). Multifunctional Conductive Nanoporous Carbon Honeycombs for Electrothermal Direct Air Capture. Advanced Materials. https://doi.org/10.1002/adma.75704
Vancouver
Ji Z, Jayakumar S, Limpo CMA, Ong YK, Madhav A, Trubyanov M, et al. Multifunctional Conductive Nanoporous Carbon Honeycombs for Electrothermal Direct Air Capture. Advanced Materials. 2026. doi:10.1002/adma.75704
BibTeX
@article{Ji2026,
author = {Ji, Zekai and Jayakumar, Sanjeevi and Limpo, Carlos Maria Alava and Ong, Yong Kang and Madhav, Aravind and Trubyanov, Maxim and Novoselov, Kostya S and Lee, Jong Hak and Özyilmaz, Barbaros},
title = {Multifunctional Conductive Nanoporous Carbon Honeycombs for Electrothermal Direct Air Capture},
journal = {Advanced Materials},
year = {2026},
doi = {10.1002/adma.75704}
}
EUVIMED