EUVIMEDEUVIMED entdecken
Crossref

Innovative Additive Manufacturing of Ultrahigh‐Strength and Heat‐Resistant Aluminum Alloy

Chaolin Tan iD, Li Zhao, Tianshu Liu iD, Jakub Mikula, Peng Chen iD, Fern Lan Ng, Robert Laskowski iD, Kun Zhou iD

Advanced Materials · 2026-11 · 38 (62)

DOI: 10.1002/adma.74966 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Materials, online erschienen am 11.09.2026. Verfasst von Chaolin Tan und 7 weiteren Autor:innen. Beteiligte Einrichtung: School of Metallic Materials and Advanced Manufacturing, Soochow University, Suzhou, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 71 Literaturangaben. Gefördert von: National Natural Science Foundation of China, 2022 MTC Young Individual Research Grants, Agency for Science, Technology and Research (A*STAR).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing (AM) advances the use of complex‐geometry aluminum (Al) alloys for lightweight aerospace components. However, AM of high‐strength Al alloys is challenging due to their inherent high susceptibility to cracking. Inoculating with scandium or zirconium effectively suppresses cracking in AM Al alloys but is costly. This work designs a low‐cost AA7075 Al wire with TiC and Ti duplex inoculants, followed by an innovative annular laser beam AM process that produces a smoother melt‐pool temperature gradient, reducing susceptibility to cracking. Crack‐free, equiaxed, fine‐grained microstructures are achieved throughout the printed sample and, together with multi‐type precipitates at multiple scales, yield good homogeneity in mechanical properties and excellent strength‐ductility synergies at both room and high temperatures. The tensile yield strength (YS) reaches 501–511 MPa with ductility of 7.3%–8.1%, comparable to wrought AA7075 alloy and superior to almost all laser‐deposited Al alloys. Additionally, the YS at 250°C reaches 275 MPa, which is higher than that of almost all AM‐printed Al alloys reported to date. This material‐process co‐innovation strategy solves multiple challenges in AM Al alloys (i.e., material printability, microstructural homogeneity, mechanical anisotropy, strength‐ductility trade‐off, high‐temperature strength, and cost efficiency), and could be generally applied to other hot‐cracking‐susceptible and poorly printable materials.

Schlagwörter

Stichwörter der Autor:innen

alloy designannular laser beamcoaxial wire additive manufacturingheat‐resistant materialsinoculation treatmentmicrostructure homogeneitythermal gradient

Autor:innen und Institutionen

  • School of Metallic Materials and Advanced Manufacturing, Soochow University, Suzhou, China.
  • Singapore Institute of Manufacturing Technology (SIMTech), Agency for Science, Technology and Research (A*STAR), Singapore, Singapore.
  • Institute of High Performance Computing (IHPC), Agency for Science, Technology and Research (A*STAR), Singapore, Singapore.
  • Singapore Centre for 3D Printing, School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore, Singapore.

ORCID-Profile: Chaolin Tan, Tianshu Liu, Peng Chen, Robert Laskowski, Kun Zhou

Förderung

  • National Natural Science Foundation of China
  • 2022 MTC Young Individual Research Grants
  • Agency for Science, Technology and Research (A*STAR)

Zitieren

APA

Tan, C., Zhao, L., Liu, T., Mikula, J., Chen, P., Ng, F. L., Laskowski, R., & Zhou, K. (2026). Innovative Additive Manufacturing of Ultrahigh‐Strength and Heat‐Resistant Aluminum Alloy. Advanced Materials, 38(62). https://doi.org/10.1002/adma.74966

Vancouver

Tan C, Zhao L, Liu T, Mikula J, Chen P, Ng FL, et al. Innovative Additive Manufacturing of Ultrahigh‐Strength and Heat‐Resistant Aluminum Alloy. Advanced Materials. 2026;38(62). doi:10.1002/adma.74966

BibTeX
@article{Tan2026,
  author = {Tan, Chaolin and Zhao, Li and Liu, Tianshu and Mikula, Jakub and Chen, Peng and Ng, Fern Lan and Laskowski, Robert and Zhou, Kun},
  title = {Innovative Additive Manufacturing of Ultrahigh‐Strength and Heat‐Resistant Aluminum Alloy},
  journal = {Advanced Materials},
  year = {2026},
  volume = {38},
  number = {62},
  doi = {10.1002/adma.74966}
}
Kostenlos starten →