EUVIMEDEUVIMED entdecken
Crossref

Negative Thermal Expansion Material‐Mediated Stress Engineering for Enhancing the Mechanical and Thermal Stability of Flexible Perovskite Solar Cells

Yingchen Li, Chao Liu, Wuchen Xiang, Hongkun Cai iD, Qinwen Guo, Jifeng Liu, Juan Li, Jian Ni, Jianjun Zhang

Advanced Materials · 2026-06 · 38 (34)

DOI: 10.1002/adma.73390 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Materials, online erschienen am 15.05.2026. Verfasst von Yingchen Li und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Micro-Nano Electronics, College of Electronic Information and Optical Engineering, Nankai University, Tianjin, P. R. China. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 34 Literaturangaben. Gefördert von: National Natural Science Foundation of China, Tianjin Science and Technology Plan Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Flexible perovskite solar cells (FPSCs) offer lightweight, high‐efficiency, flexibility, residual stress from substrate‐perovskite thermal expansion coefficients (CTE) /lattice mismatch drives grain‐boundary cracking, defect rise, and delamination, limiting stability and efficiency gains. Substrates with a low CTE limit the lattice contraction of perovskites during the cooling process, which leads to the generation of tensile strain. In this paper, a strategy for regulating the CTE was developed by adding potassium pyrophosphate (KPP) to perovskite precursors. The P─O bonds in KPP not only form coordination bonds with Pb 2+ , but also form hydrogen bonds with FA + , reducing the defect state density and improving the stability of the device. More importantly, KPP with the characteristic of “thermal contraction and cold expansion” can significantly relieve the residual stress in the perovskite thin film. After 100 thermal cycles between 25°C and 100°C, its thermal cycling stability remains at 90%, while that of the control group is only 70.9%. Therefore, the optimized FPSCs achieved a power conversion efficiency (PCE) of 25.41%. In addition, unpackaged devices exhibit mechanical robustness at T 92 > 10 ,000 bending cycles (with a bending radius of 5 mm), operational stability at T 91 >1000 h.

Schlagwörter

Stichwörter der Autor:innen

KPPflexible perovskite solar cellsnegative thermal expansion materialresidual stress

Autor:innen und Institutionen

  • Department of Micro-Nano Electronics, College of Electronic Information and Optical Engineering, Nankai University, Tianjin, P. R. China.
  • State Key Laboratory of Photovoltaic Materials and Cells, Tianjin, P. R. China.
  • Engineering Research Center of Thin Film Photoelectronic Technology of Ministry of Education, Tianjin, P. R. China.
  • Key Laboratory of Efficient Utilization of Solar Energy of Tianjin, Tianjin, P. R. China.

ORCID-Profile: Hongkun Cai

Förderung

  • National Natural Science Foundation of China
  • Tianjin Science and Technology Plan Project

Zitieren

APA

Li, Y., Liu, C., Xiang, W., Cai, H., Guo, Q., Liu, J., Li, J., Ni, J., & Zhang, J. (2026). Negative Thermal Expansion Material‐Mediated Stress Engineering for Enhancing the Mechanical and Thermal Stability of Flexible Perovskite Solar Cells. Advanced Materials, 38(34). https://doi.org/10.1002/adma.73390

Vancouver

Li Y, Liu C, Xiang W, Cai H, Guo Q, Liu J, et al. Negative Thermal Expansion Material‐Mediated Stress Engineering for Enhancing the Mechanical and Thermal Stability of Flexible Perovskite Solar Cells. Advanced Materials. 2026;38(34). doi:10.1002/adma.73390

BibTeX
@article{Li2026,
  author = {Li, Yingchen and Liu, Chao and Xiang, Wuchen and Cai, Hongkun and Guo, Qinwen and Liu, Jifeng and Li, Juan and Ni, Jian and Zhang, Jianjun},
  title = {Negative Thermal Expansion Material‐Mediated Stress Engineering for Enhancing the Mechanical and Thermal Stability of Flexible Perovskite Solar Cells},
  journal = {Advanced Materials},
  year = {2026},
  volume = {38},
  number = {34},
  doi = {10.1002/adma.73390}
}
Kostenlos starten →