EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Additively Manufacturable High‐Strength Aluminum Alloys with Coarsening‐Resistant Microstructures Achieved via Rapid Solidification

S Mohadeseh Taheri-Mousavi iD, Michael Xu, Florian Hengsbach, Clay Houser, Zhaoxuan Ge, Benjamin Glaser, Shaolou Wei iD, Mirko Schaper, James M LeBeau, Greg B Olson, A John Hart

Advanced Materials · 2026-01 · 38 (4)

DOI: 10.1002/adma.202509507 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Materials, online erschienen am 02.10.2025. Verfasst von S Mohadeseh Taheri-Mousavi und 10 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA, 02139, USA. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Army Research Laboratory, Division of Civil, Mechanical and Manufacturing Innovation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additively manufactured aluminum (Al) alloys with high strength have broad industrial applications. Strength promotion necessitates a high‐volume fraction of small, closely spaced precipitates to effectively impede dislocation motion. Here, it is shown that for certain compositions in the Al‐Er‐Zr‐Y‐Yb‐Ni alloy class, L1 2 ‐Al 3 M phases, the primary strength contributor, can initially precipitate as submicron‐scale (≈100 nm) metastable ternary phases under the rapid solidification of powder bed additive manufacturing; yet the subsequent coarsening‐resistant L1 2 ‐Al 3 M phases that precipitate during heat treatment remain at the nanometer scale, imparting high strength. A candidate alloy is designed using hybrid calculation of phase diagrams (CALPHAD)‐based integrated computational materials engineering (ICME) and Bayesian optimization algorithms. Powder is manufactured for this alloy and is additively manufactured into crack‐free macroscale specimens with a strength that is five‐fold that of the equivalent cast alloy and comparable to wrought Al 7075. After aging at 400 °C for 8 h, the room‐temperature tensile strength reaches 395 MPa, which is 50% stronger than the best‐known benchmark printable Al alloy. This integrated computational‐experimental workflow shows the considerable potential to exploit rapid solidification in additive manufacturing to design alloys with commercially deployable properties.

Schlagwörter

Stichwörter der Autor:innen

CALPHAD‐based ICMEcoarsening resistancehigh strengthmachine learningprintable aluminum alloys

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA, 02139, USA.
  • Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA, 02139, USA.
  • Department of Materials Science and Engineering, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA, 15213, USA.
  • Department of Mechanical Engineering, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA, 15213, USA.
  • Department of Mechanical Engineering, Paderborn University, Mersinweg 9, 33100, Paderborn, Germany.
  • Department of Materials Science and Engineering, Northwestern University, Evanston, IL, 60208, USA.

ORCID-Profile: S Mohadeseh Taheri-Mousavi, Shaolou Wei

Förderung

  • Army Research Laboratory
  • Division of Civil, Mechanical and Manufacturing Innovation

Zitieren

APA

Taheri-Mousavi, S. M., Xu, M., Hengsbach, F., Houser, C., Ge, Z., Glaser, B., Wei, S., Schaper, M., LeBeau, J. M., Olson, G. B., & Hart, A. J. (2026). Additively Manufacturable High‐Strength Aluminum Alloys with Coarsening‐Resistant Microstructures Achieved via Rapid Solidification. Advanced Materials, 38(4). https://doi.org/10.1002/adma.202509507

Vancouver

Taheri-Mousavi SM, Xu M, Hengsbach F, Houser C, Ge Z, Glaser B, et al. Additively Manufacturable High‐Strength Aluminum Alloys with Coarsening‐Resistant Microstructures Achieved via Rapid Solidification. Advanced Materials. 2026;38(4). doi:10.1002/adma.202509507

BibTeX
@article{TaheriMousavi2026,
  author = {Taheri-Mousavi, S Mohadeseh and Xu, Michael and Hengsbach, Florian and Houser, Clay and Ge, Zhaoxuan and Glaser, Benjamin and Wei, Shaolou and Schaper, Mirko and LeBeau, James M and Olson, Greg B and Hart, A John},
  title = {Additively Manufacturable High‐Strength Aluminum Alloys with Coarsening‐Resistant Microstructures Achieved via Rapid Solidification},
  journal = {Advanced Materials},
  year = {2026},
  volume = {38},
  number = {4},
  doi = {10.1002/adma.202509507}
}
Kostenlos starten →