Volumetric 3D Printing and Melt‐Electrowriting to Fabricate Implantable Reinforced Cardiac Tissue Patches
Advanced Materials · 2025-11 · 37 (45)
DOI: 10.1002/adma.202504765 ↗Kurz gefasst
Fachartikel in der Zeitschrift Advanced Materials, online erschienen am 05.08.2025. Verfasst von Lewis S Jones und 12 weiteren Autor:innen. Beteiligte Einrichtung: Soft Robotics Laboratory, ETH Zurich, Tannenstrasse 3, Zurich, 8092, Switzerland. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Tissue Scaffolds, Prostheses and Implants. Die Arbeit wurde bisher 25-mal zitiert (Crossref) und nennt 60 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: University of Zurich Innopool, Mäxi Foundation, UBS to the ETH Foundation.
Abstract (Originalsprache)
Cardiac patches to repair myocardial defects require mechanically stable materials that prevent bleeding and can be implanted via suturing. The current clinical standard, bovine pericardial patches (BPPs), serve this purpose but do not degrade or integrate with the myocardium, limiting their long‐term effectiveness. Here, we present the reinforced cardiac tissue patch (RCPatch). This multimaterial patch comprises a stiffness‐tuned, cardiomyocyte‐infiltrated 3D metamaterial and a suturable, hydrogel‐infiltrated mesh to reduce permeability and bleeding. Anisotropic metamaterials are designed and computationally optimized using a generative modeling approach and fabricated from poly(ε‐caprolactone) (PCL) via volumetric 3D printing (VP). The metamaterial supports the infiltration of cardiomyocytes, which are viable and contract in vitro. The implantability and low blood permeability of the patch is enabled by adding a melt‐electrowritten (MEW) mesh infiltrated with a fibrin hydrogel. In an acute large animal trial, the RCPatch was applied on an induced myocardial defect, where it withstood intraventricular blood pressure, prevented bleeding, and enabled hemodynamic restabilization (intraventricular pressure of 81 mmHg before, vs 66 mmHg after implantation). These findings establish a scalable framework for fabricating cardiac tissue patches that integrate mechanical reinforcement with biological function, offering a surgically implantable and future regenerative solution for intraventricular myocardial repair.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Soft Robotics Laboratory, ETH Zurich, Tannenstrasse 3, Zurich, 8092, Switzerland.
- Department of Cardiac Surgery, University Hospital Zurich, Rämistrasse 100, Zurich, 8091, Switzerland.
- Department of Cardiac Surgery, City Hospital Zurich-Triemli, Center for Experimental and Translational Cardiology (CTEC), University of Zurich, Zurich, 8952, Switzerland.
- Polymer Chemistry and Biomaterials Group, Centre of Macromolecular Chemistry, Department of Organic and Macromolecular Chemistry, Ghent University, Krijgslaan 281 S4, Ghent, 9000, Belgium.
- Institute for Biomechanics, ETH Zurich, Gloriastrasse 37-39, Zurich, 8092, Switzerland.
- Center for Preclinical Development, University Hospital Zurich, University of Zurich, Strickhofstrasse 40a, Zürich, 8057, Switzerland.
ORCID-Profile: Lewis S Jones, Hector Rodriguez Cetina Biefer, Manuel Mekkattu, Quinten Thijssen, Alessio Amicone, Anna Bock, Miriam Weisskopf, Li Zheng, Melanie Generali, Robert K Katzschmann, Omer Dzemali
Förderung
- University of Zurich Innopool
- Mäxi Foundation
- UBS to the ETH Foundation
- Research Foundation - Flanders
- Swiss National Science Foundation
- Schweizerischer Nationalfonds zur Förderung der Wissenschaftlichen Forschung
Zitieren
APA
Jones, L. S., Rodriguez Cetina Biefer, H., Mekkattu, M., Thijssen, Q., Amicone, A., Bock, A., Weisskopf, M., Zorndt, D., Meier, D., Zheng, L., Generali, M., Katzschmann, R. K., & Dzemali, O. (2025). Volumetric 3D Printing and Melt‐Electrowriting to Fabricate Implantable Reinforced Cardiac Tissue Patches. Advanced Materials, 37(45). https://doi.org/10.1002/adma.202504765
Vancouver
Jones LS, Rodriguez Cetina Biefer H, Mekkattu M, Thijssen Q, Amicone A, Bock A, et al. Volumetric 3D Printing and Melt‐Electrowriting to Fabricate Implantable Reinforced Cardiac Tissue Patches. Advanced Materials. 2025;37(45). doi:10.1002/adma.202504765
BibTeX
@article{Jones2025,
author = {Jones, Lewis S and Rodriguez Cetina Biefer, Hector and Mekkattu, Manuel and Thijssen, Quinten and Amicone, Alessio and Bock, Anna and Weisskopf, Miriam and Zorndt, Dennis and Meier, Debora and Zheng, Li and Generali, Melanie and Katzschmann, Robert K and Dzemali, Omer},
title = {Volumetric 3D Printing and Melt‐Electrowriting to Fabricate Implantable Reinforced Cardiac Tissue Patches},
journal = {Advanced Materials},
year = {2025},
volume = {37},
number = {45},
doi = {10.1002/adma.202504765}
}
EUVIMED