EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Design of Electrified Fiber Sorbents for Direct Air Capture with Electrically‐Driven Temperature Vacuum Swing Adsorption

Young Hun Lee, Jung Hun Lee, Hwajoo Joo, Michael Massen-Hane, Injun Park, Soohyeon Rho, Aqil Jamal, T Alan Hatton, Dong-Yeun Koh iD

Advanced Materials · 2025-11 · 37 (45)

DOI: 10.1002/adma.202504542 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Materials, 2025-08. Verfasst von Young Hun Lee und 8 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology, Daejeon, 34141, South Korea. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: National Research Foundation of Korea, Saudi Aramco.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Joule heating is becoming accepted as a highly efficient regeneration technique for temperature vacuum swing adsorption in direct air capture (DAC). This acknowledgment arises from its ability to rapidly generate and transfer heat, along with the convenience of obtaining electrical power from renewable sources. This study presents a unique electrified fiber sorbent (i.e., e‐fiber) design that facilitates Joule heating, enabling energy‐efficient electrically‐driven temperature‐vacuum swing adsorption (e‐TVSA) for DAC. The e‐fiber sorbent is produced via a dip coating technique, in which a silver composite solution is applied to the surface of an open‐porous polymer matrix. The resulting ultra‐thin, interconnected porous conductive layer on the fiber surface not only minimizes the increase in diffusion resistance even after the surface coating process but also offers exceptionally low electrical resistance (0.5 Ω cm −1 ). The e‐fiber sorbent module achieves a desorption temperature of 110 °C in 80 s at 3 V. Notably, only a 5% reduction in capacity is recorded following repeated cycles of e‐TVSA at a CO 2 concentration of 400 ppm. The complicated nature of heat transfer processes is clarified caused by Joule heating in the e‐fiber sorbent module through detailed case studies conducted with computational simulations, offering insights for design optimization and system engineering.

Schlagwörter

Stichwörter der Autor:innen

Joule heatingdirect air capturedry‐jet wet‐quench spinningelectrically‐driven temperature‐vacuum swing adsorption (e‐TVSA)electrified fiber sorbents

Autor:innen und Institutionen

  • Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology, Daejeon, 34141, South Korea.
  • Department of Chemical Engineering, Massachusetts Institute of Technology, Cambridge, MA, 02139, USA.
  • Material and Component Convergence R&D Department, Korea Institute of Industrial Technology (KITECH), Ansan, 15588, South Korea.
  • Carbon Management Division, Research and Development Center, Saudi Aramco, Dhahran, 31311, Saudi Arabia.
  • Saudi Aramco-KAIST CO2 Management Center, Daejeon, 34141, South Korea.

ORCID-Profile: Dong-Yeun Koh

Förderung

  • National Research Foundation of Korea
  • Saudi Aramco

Zitieren

APA

Lee, Y. H., Lee, J. H., Joo, H., Massen-Hane, M., Park, I., Rho, S., Jamal, A., Alan Hatton, T., & Koh, D. Y. (2025). Design of Electrified Fiber Sorbents for Direct Air Capture with Electrically‐Driven Temperature Vacuum Swing Adsorption. Advanced Materials, 37(45). https://doi.org/10.1002/adma.202504542

Vancouver

Lee YH, Lee JH, Joo H, Massen-Hane M, Park I, Rho S, et al. Design of Electrified Fiber Sorbents for Direct Air Capture with Electrically‐Driven Temperature Vacuum Swing Adsorption. Advanced Materials. 2025;37(45). doi:10.1002/adma.202504542

BibTeX
@article{Lee2025,
  author = {Lee, Young Hun and Lee, Jung Hun and Joo, Hwajoo and Massen-Hane, Michael and Park, Injun and Rho, Soohyeon and Jamal, Aqil and Alan Hatton, T and Koh, Dong-Yeun},
  title = {Design of Electrified Fiber Sorbents for Direct Air Capture with Electrically‐Driven Temperature Vacuum Swing Adsorption},
  journal = {Advanced Materials},
  year = {2025},
  volume = {37},
  number = {45},
  doi = {10.1002/adma.202504542}
}
Kostenlos starten →