3D Bioprinting of Liquid High‐Cell‐Proportion Bioinks in Liquid Granular Bath
Advanced Materials · 2024
DOI: 10.1002/adma.202412127 ↗Kurz gefasst
Fachartikel in der Zeitschrift Advanced Materials, 2024. Verfasst von Jinhong Jiang und 7 weiteren Autor:innen. Beteiligte Einrichtung: Health Science Center, Ningbo University, Ningbo, Zhejiang, 315211, China. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Bioprinting, Ink. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 65 Literaturangaben. Gefördert von: General scientific Research Project of Zhejiang Education Department, Open Foundation of the State Key Laboratory of Fluid Power and Mechatronic Systems, Fundamental Research Funds for the Provincial Universities of Zhejiang.
Abstract (Originalsprache)
Embedded 3D bioprinting techniques have emerged as a powerful method to fabricate 3D engineered constructs using low strength bioinks; however, there are challenges in simultaneously satisfying the requirements of high‐cell‐activity, high‐cell‐proportion, and low‐viscosity bioinks. In particular, the printing capacity of embedded 3D bioprinting is limited as two main challenges: spreading and diffusion, especially for liquid, high‐cell‐activity bioinks that can facilitate high‐cell‐proportion. Here, a liquid‐in‐liquid 3D bioprinting (LL3DBP) strategy is developed, which used a liquid granular bath to prevent the spreading of liquid bioinks during 3D printing, and electrostatic interaction between the liquid bioinks and liquid granular baths is found to effectively prevent the diffusion of liquid bioinks. As an example, the printing of positively charged 5% w/v gelatin methacryloyl (GelMA) in a liquid granular bath prepared with negatively charged κ‐carrageenan is proved to be achievable. By LL3DBP, printing capacity is greatly advanced and bioinks with over 90% v/v cell can be printed, and printed structures with high‐cell‐proportion exhibit excellent bioactivity.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Health Science Center, Ningbo University, Ningbo, Zhejiang, 315211, China.
- Research Institute for Medical and Biological Engineering, Ningbo University, Ningbo, Zhejiang, 315211, China.
- Faculty of Materials Science and Chemical Engineering, Ningbo University, Ningbo, Zhejiang, 315211, China.
- State Key Laboratory of Fluid Power and Mechatronic Systems, College of Mechanical Engineering, Zhejiang University, Hangzhou, Zhejiang, 310027, China.
ORCID-Profile: Lei Shao
Förderung
- General scientific Research Project of Zhejiang Education Department
- Open Foundation of the State Key Laboratory of Fluid Power and Mechatronic Systems
- Fundamental Research Funds for the Provincial Universities of Zhejiang
- Natural Science Foundation of Ningbo Municipality
- Natural Science Foundation of Zhejiang Province
Zitieren
APA
Jiang, J., Yuan, C., Zhang, X., Gu, L., Yao, Y., Wang, X., He, Y., & Shao, L. (2024). 3D Bioprinting of Liquid High‐Cell‐Proportion Bioinks in Liquid Granular Bath. Advanced Materials. https://doi.org/10.1002/adma.202412127
Vancouver
Jiang J, Yuan C, Zhang X, Gu L, Yao Y, Wang X, et al. 3D Bioprinting of Liquid High‐Cell‐Proportion Bioinks in Liquid Granular Bath. Advanced Materials. 2024. doi:10.1002/adma.202412127
BibTeX
@article{Jiang2024,
author = {Jiang, Jinhong and Yuan, Chenhui and Zhang, Xinyu and Gu, Lin and Yao, Yudong and Wang, Xueping and He, Yong and Shao, Lei},
title = {3D Bioprinting of Liquid High‐Cell‐Proportion Bioinks in Liquid Granular Bath},
journal = {Advanced Materials},
year = {2024},
doi = {10.1002/adma.202412127}
}
EUVIMED