Bottom Contact Engineering for Ambient Fabrication of >25% Durable Perovskite Solar Cells
Advanced Materials · 2024-10 · 36 (41)
DOI: 10.1002/adma.202409261 ↗Kurz gefasst
Fachartikel in der Zeitschrift Advanced Materials, online erschienen am 02.08.2024. Verfasst von Ligang Yuan und 14 weiteren Autor:innen. Beteiligte Einrichtung: Key Laboratory for Optoelectronic Information Perception and Instrumentation of Jiangxi Province, Key Laboratory of Nondestructive Testing Ministry o…. Die Arbeit wurde bisher 69-mal zitiert (Crossref) und nennt 48 Literaturangaben. Gefördert von: National Key Research and Development Program of China, PhD Research Start-up Funds from the Nanchang Hangkong University, National Natural Science Foundation of China.
Abstract (Originalsprache)
The bottom contact in perovskite solar cells (PSCs) is easy to cause deep trap states and severe instability issues, especially under maximum power point tracking (MPPT). In this study, sodium gluconate (SG) is employed to disperse tin oxide (SnO 2 ) nanoparticles (NPs) and regulate the interface contact at the buried interface. The SG‐SnO 2 electron transfer layer (ETL) enabled the deposition of pinhole‐free perovskite films in ambient air and improved interface contact by bridging effect. SG‐SnO 2 PSCs achieved an impressive power conversion efficiency (PCE) of 25.34% (certified as 25.17%) with a high open‐circuit voltage ( V OC ) exceeding 1.19 V. The V OC loss is less than 0.34 V relative to the 1.53 eV bandgap, and the fill factor (FF) loss is only 2.02% due to the improved contact. The SG‐SnO 2 PSCs retained around 90% of their initial PCEs after 1000 h operation (T 90 = 1000 h), higher than T 80 = 1000 h for the control SnO 2 PSC. Microstructure analysis revealed that light‐induced degradation primarily occurred at the buried holes and grain boundaries and highlighted the importance of bottom‐contact engineering.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Key Laboratory for Optoelectronic Information Perception and Instrumentation of Jiangxi Province, Key Laboratory of Nondestructive Testing Ministry of Education, School of the Testing and Photoelectric Engineering, Nanc…
- School of Environment and Energy, State Key Laboratory of Luminescent Materials and Devices, Guangdong Provincial Key Laboratory of Solid Wastes Pollution Control and Recycling, South China University of Technology, Gua…
- Institute of Materials for Electronics and Energy Technology (i-MEET), Friedrich-Alexander-University Erlangen-Nüremberg, Martensstraße 7, 91058, Erlangen, Germany.
- Research Institute of Frontier Science, Southwest Jiaotong University, Chengdu, 610031, China.
- Department of Physics and William Mong Institute of Nano Science and Technology, The Hong Kong University of Science and Technology, Clearwater Bay, Hong Kong, 999077, P. R. China.
- Department of Physics, The Chinese University of Hong Kong, Shatin, Hong Kong, 999077, P. R. China.
ORCID-Profile: Ligang Yuan, Keyou Yan
Förderung
- National Key Research and Development Program of China
- PhD Research Start-up Funds from the Nanchang Hangkong University
- National Natural Science Foundation of China
- Training Program for Academic and Technical Leaders of Major Disciplines in Jiangxi Province
- Jiangxi Provincial Natural Science Foundation
- Fundamental Research Fund for the Central Universities, SWJTU
- Novel Interdisciplinary Cultivation Fund from Southwest Jiaotong University
- The Natural Science Foundation of Sichuan Province
Zitieren
APA
Yuan, L., Zou, S., Zhang, K., Huang, P., Dong, Y., Wang, J., Fan, K., Lam, M. Y., Wu, X., Cheng, W., Tang, R., Chen, W., Liu, W., Wong, K. S., & Yan, K. (2024). Bottom Contact Engineering for Ambient Fabrication of >25% Durable Perovskite Solar Cells. Advanced Materials, 36(41). https://doi.org/10.1002/adma.202409261
Vancouver
Yuan L, Zou S, Zhang K, Huang P, Dong Y, Wang J, et al. Bottom Contact Engineering for Ambient Fabrication of >25% Durable Perovskite Solar Cells. Advanced Materials. 2024;36(41). doi:10.1002/adma.202409261
BibTeX
@article{Yuan2024,
author = {Yuan, Ligang and Zou, Shibing and Zhang, Kaicheng and Huang, Peng and Dong, Yuyan and Wang, Jiarong and Fan, Kezhou and Lam, Man Yu and Wu, Xiao and Cheng, Wei and Tang, Ruijia and Chen, Wenhao and Liu, Weiqing and Wong, Kam Sing and Yan, Keyou},
title = {Bottom Contact Engineering for Ambient Fabrication of >25% Durable Perovskite Solar Cells},
journal = {Advanced Materials},
year = {2024},
volume = {36},
number = {41},
doi = {10.1002/adma.202409261}
}
EUVIMED