EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Customizable Fabrication of 2D and Conformal Multielectrode Arrays for 3D Printed Organotypic Bioelectronic Interfaces

Ernest Cheah iD, Xinchao Gao iD, Wei Qi Jaw iD, Guo Liang Goh iD, Jia Min Lee iD, Chongquan Huang iD, Sing Yian Chew iD, Wai Yee Yeong iD

Advanced Healthcare Materials · 2025

DOI: 10.1002/adhm.202502757 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Healthcare Materials, 2025. Verfasst von Ernest Cheah und 7 weiteren Autor:innen. Beteiligte Einrichtung: Singapore Centre for 3D Printing, Nanyang Technological University, Singapore, 639798, Singapore. Hauptthemen laut MEDLINE: Printing, Three-Dimensional. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 58 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: National Research Foundation Singapore.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Organotypic 3D tissue models require precise electrophysiological interfaces to study function and disease. Multi‐electrode arrays (MEAs) are essential for recording and stimulation, yet conventional fabrication methods are costly and time‐intensive. This study demonstrates aerosol jet printing (AJP) of gold nanoparticles onto flexible polyimide substrates to produce fully gold, biocompatible MEAs for rapid customization of MEAs. Fabrication time is reduced from ≈320 min (photolithography) to ≈175 min, with minimal material waste. Printed electrodes achieve low impedance (0.05 kΩ µm − 2 at 1 kHz) with stable performance over 14 days. Coating with poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT/PSS) increases charge injection capacity and maintains stability over 200 000 stimulation pulses. Cytocompatibility is confirmed through direct 3D bioprinting of C2C12 myoblast‐laden gelatin methacryloyl (GelMA) onto MEAs, achieving 70–80% viability. Electrical stimulation induces myoblast alignment, and extracellular recordings from primary cortical neurons and HL‐1 cardiomyocytes yield signal‐to‐noise ratios of 20.89 and 16.62 dB, respectively. Integration into 3D‐printed hydrogel conduits demonstrates conformal application and enhanced cell organization. These findings establish AJP as a scalable fabrication approach for customizable MEAs, supporting the development of advanced bioelectronic interfaces for organotypic tissue models.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalAnimalsMiceGoldPolystyrenesMetal NanoparticlesElectrodesBioprintingCell LineGelatinPolymersMethacrylates

Stichwörter der Autor:innen

3D cell printingaerosol jet printingbioelectronic interfaceselectrophysiological recordingmulti‐electrode arrays

Substanzen

GoldPolystyrenesGelatingelatin methacryloylPolymersMethacrylates

Autor:innen und Institutionen

  • Singapore Centre for 3D Printing, Nanyang Technological University, Singapore, 639798, Singapore.
  • Singapore Institute of Manufacturing Technology (SIMTech), Agency for Science, Technology and Research (A⁎STAR), Singapore, 636732, Singapore.
  • School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore, 639798, Singapore.
  • School of Chemistry, Chemical Engineering and Biotechnology, Nanyang Technological University, Singapore, 637371, Singapore.
  • Neuroscience@NTU, Interdisciplinary Graduate Programme, Nanyang Technological University, Singapore, 639798, Singapore.
  • Lee Kong Chian School of Medicine, Nanyang Technological University, Singapore, 308232, Singapore.

ORCID-Profile: Ernest Cheah, Xinchao Gao, Wei Qi Jaw, Guo Liang Goh, Jia Min Lee, Chongquan Huang, Sing Yian Chew, Wai Yee Yeong

Förderung

  • National Research Foundation Singapore

Zitieren

APA

Cheah, E., Gao, X., Jaw, W. Q., Goh, G. L., Lee, J. M., Huang, C., Chew, S. Y., & Yeong, W. Y. (2025). Customizable Fabrication of 2D and Conformal Multielectrode Arrays for 3D Printed Organotypic Bioelectronic Interfaces. Advanced Healthcare Materials. https://doi.org/10.1002/adhm.202502757

Vancouver

Cheah E, Gao X, Jaw WQ, Goh GL, Lee JM, Huang C, et al. Customizable Fabrication of 2D and Conformal Multielectrode Arrays for 3D Printed Organotypic Bioelectronic Interfaces. Advanced Healthcare Materials. 2025. doi:10.1002/adhm.202502757

BibTeX
@article{Cheah2025,
  author = {Cheah, Ernest and Gao, Xinchao and Jaw, Wei Qi and Goh, Guo Liang and Lee, Jia Min and Huang, Chongquan and Chew, Sing Yian and Yeong, Wai Yee},
  title = {Customizable Fabrication of 2D and Conformal Multielectrode Arrays for 3D Printed Organotypic Bioelectronic Interfaces},
  journal = {Advanced Healthcare Materials},
  year = {2025},
  doi = {10.1002/adhm.202502757}
}
Kostenlos starten →