EUVIMEDEUVIMED entdecken
Open Access

Embedded 3D Bioprinting of Collagen Inks into Microgel Baths to Control Hydrogel Microstructure and Cell Spreading

Lucia G Brunel iD, Fotis Christakopoulos iD, David Kilian iD, Betty Cai iD, Sarah M Hull iD, David Myung, Sarah C Heilshorn iD

Advanced Healthcare Materials · 2024-10 · 13 (25)

DOI: 10.1002/adhm.202303325 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Healthcare Materials, online erschienen am 26.02.2024. Verfasst von Lucia G Brunel und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical Engineering, Stanford University, Stanford, CA, 94305, USA. Hauptthemen laut MEDLINE: Bioprinting, Collagen, Printing, Three-Dimensional, Mesenchymal Stem Cells. Die Arbeit wurde bisher 51-mal zitiert (Crossref) und nennt 74 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: NIH HHS, NEI NIH HHS, NHLBI NIH HHS.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Microextrusion‐based 3D bioprinting into support baths has emerged as a promising technique to pattern soft biomaterials into complex, macroscopic structures. It is hypothesized that interactions between inks and support baths, which are often composed of granular microgels, can be modulated to control the microscopic structure within these macroscopic‐printed constructs. Using printed collagen bioinks crosslinked either through physical self‐assembly or bioorthogonal covalent chemistry, it is demonstrated that microscopic porosity is introduced into collagen inks printed into microgel support baths but not bulk gel support baths. The overall porosity is governed by the ratio between the ink's shear viscosity and the microgel support bath's zero‐shear viscosity. By adjusting the flow rate during extrusion, the ink's shear viscosity is modulated, thus controlling the extent of microscopic porosity independent of the ink composition. For covalently crosslinked collagen, printing into support baths comprised of gelatin microgels (15‐50 µm) results in large pores (≈40 µm) that allow human corneal mesenchymal stromal cells (MSCs) to readily spread, while control samples of cast collagen or collagen printed in non‐granular support baths do not allow cell spreading. Taken together, these data demonstrate a new method to impart controlled microscale porosity into 3D printed hydrogels using granular microgel support baths.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

BioprintingCollagenPrinting, Three-DimensionalMesenchymal Stem CellsHydrogelsInkHumansMicrogelsPorosityViscosityAnimals

Stichwörter der Autor:innen

collagen inksembedded bioprintinghydrogel microstructuresupport baths

Substanzen

CollagenHydrogelsMicrogels

Autor:innen und Institutionen

  • Department of Chemical Engineering, Stanford University, Stanford, CA, 94305, USA.
  • Department of Materials Science and Engineering, Stanford University, Stanford, CA, 94305, USA.
  • Department of Ophthalmology, Byers Eye Institute, Stanford University School of Medicine, Palo Alto, CA, 94303, USA.
  • VA Palo Alto Health Care System, Palo Alto, CA, 94304, USA.

ORCID-Profile: Lucia G Brunel, Fotis Christakopoulos, David Kilian, Betty Cai, Sarah M Hull, Sarah C Heilshorn

Förderung

  • NIH HHS
  • NEI NIH HHS
  • NHLBI NIH HHS
  • National Science Foundation
  • Stanford Bio-X Interdisciplinary Graduate Fellowship
  • Research to Prevent Blindness
  • Stanford Knight-Hennessy Scholars Program
  • Swiss National Science Foundation

Zitieren

APA

Brunel, L. G., Christakopoulos, F., Kilian, D., Cai, B., Hull, S. M., Myung, D., & Heilshorn, S. C. (2024). Embedded 3D Bioprinting of Collagen Inks into Microgel Baths to Control Hydrogel Microstructure and Cell Spreading. Advanced Healthcare Materials, 13(25). https://doi.org/10.1002/adhm.202303325

Vancouver

Brunel LG, Christakopoulos F, Kilian D, Cai B, Hull SM, Myung D, et al. Embedded 3D Bioprinting of Collagen Inks into Microgel Baths to Control Hydrogel Microstructure and Cell Spreading. Advanced Healthcare Materials. 2024;13(25). doi:10.1002/adhm.202303325

BibTeX
@article{Brunel2024,
  author = {Brunel, Lucia G and Christakopoulos, Fotis and Kilian, David and Cai, Betty and Hull, Sarah M and Myung, David and Heilshorn, Sarah C},
  title = {Embedded 3D Bioprinting of Collagen Inks into Microgel Baths to Control Hydrogel Microstructure and Cell Spreading},
  journal = {Advanced Healthcare Materials},
  year = {2024},
  volume = {13},
  number = {25},
  doi = {10.1002/adhm.202303325}
}
Kostenlos starten →