EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Assembly of Cell‐Seeded 3D Printed Hydrogel Modules with Perfusable Channel Networks

Zachary J. Geffert, Daniel Fougnier, Bo Van Durme, Jenna Grutzmacher, Ryan Clarke, Susan Cao, Zhenghao Li, Ujjwal Aryal, Jason A. Horton, Sandra Van Vlierberghe, Pranav Soman

Advanced Functional Materials · 2026-06 · 36 (44)

DOI: 10.1002/adfm.75239 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Functional Materials, online erschienen am 06.04.2026. Verfasst von Zachary J. Geffert und 10 weiteren Autor:innen. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 62 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: National Institutes of Health.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Successfully recapitulating functional tissue‐scale biological structures using additive manufacturing requires simultaneous scaling up to reach clinically relevant sizes and scaling down to incorporate internal vascular‐like features to support high cell viability. This work reports a new multiscale assembly method that integrates cell‐seeded hydrogel modules via gluing to create larger constructs. Scalability is based on an intuitive concept of stacking modules, which allows for a high degree of geometric freedom without the need for specialized equipment. Projection Stereolithography (PSLA) is used to print centimeter‐sized modules using gelatin methacryloyl aminoethyl methacrylate (GelMA‐AEMA). Each module (500 mm 3 ) contains two independent hollow features: seeding port‐arrays to facilitate cell seeding and branched channel networks to enable perfusion. New multi‐material bioreactors are developed, integrating a rigid core with a flexible skin featuring needle septa to yield a watertight seal, providing a sterile environment for perfusion culture. In parallel, a novel gluing strategy is developed, and its efficacy is demonstrated by perfusing dye through an 18‐module assembly. For cell‐seeding experiments, model stromal cells are seeded within a 2‐module assembly, followed by media perfusion. Through assembly of pre‐printed perfusable hydrogel modules, this work helps address key limitations of existing methods and advances development toward realizing large‐scale reproducible tissue constructs.

Förderung

  • National Institutes of Health

Zitieren

APA

Geffert, Z. J., Fougnier, D., Durme, B. V., Grutzmacher, J., Clarke, R., Cao, S., Li, Z., Aryal, U., Horton, J. A., Vlierberghe, S. V., & Soman, P. (2026). Assembly of Cell‐Seeded 3D Printed Hydrogel Modules with Perfusable Channel Networks. Advanced Functional Materials, 36(44). https://doi.org/10.1002/adfm.75239

Vancouver

Geffert ZJ, Fougnier D, Durme BV, Grutzmacher J, Clarke R, Cao S, et al. Assembly of Cell‐Seeded 3D Printed Hydrogel Modules with Perfusable Channel Networks. Advanced Functional Materials. 2026;36(44). doi:10.1002/adfm.75239

BibTeX
@article{Geffert2026,
  author = {Geffert, Zachary J. and Fougnier, Daniel and Durme, Bo Van and Grutzmacher, Jenna and Clarke, Ryan and Cao, Susan and Li, Zhenghao and Aryal, Ujjwal and Horton, Jason A. and Vlierberghe, Sandra Van and Soman, Pranav},
  title = {Assembly of Cell‐Seeded 3D Printed Hydrogel Modules with Perfusable Channel Networks},
  journal = {Advanced Functional Materials},
  year = {2026},
  volume = {36},
  number = {44},
  doi = {10.1002/adfm.75239}
}
Kostenlos starten →