Printed and Stretchable Triboelectric Energy Harvester Based on P(VDF‐TrFE) Porous Aerogel
Advanced Functional Materials · 2024-05 · 34 (19)
DOI: 10.1002/adfm.202312881 ↗Kurz gefasst
Fachartikel in der Zeitschrift Advanced Functional Materials, online erschienen am 17.01.2024. Verfasst von Karem Lozano Montero und 6 weiteren Autor:innen. Die Arbeit wurde bisher 53-mal zitiert (Crossref) und nennt 70 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Tekniikan Edistämissäätiö, Walter Ahlströmin Säätiö, Academy of Finland.
Abstract (Originalsprache)
Developing energy harvesting devices is crucial to mitigate the dependence on conventional and rigid batteries in wearable electronics, ensuring their autonomous operation. Nanogenerators offer a cost‐effective solution for enabling continuous operation of wearable electronics. Herein, this study proposes a novel strategy that combines freeze‐casting, freeze‐drying, and printing technologies to fabricate a fully printed triboelectric nanogenerator (TENG) based on polyvinylidene fluorid‐etrifluoroethylene P(VDF‐TrFE) porous aerogel. First, the effects of porosity and poling on the stretchability and energy harvesting capabilities of P(VDF‐TrFE) are investigated, conducting a comprehensive analysis of this porous structure's impact on the mechanical, ferroelectric, and triboelectric properties compared to solid P(VDF‐TrFE) films. The results demonstrate that structural modification of P(VDF‐TrFE) significantly enhances stretchability increasing it from 7.7% (solid) to 66.4% (porous). This modification enhances output voltage by 66% and generated charges by 48% for non‐poled P(VDF‐TrFE) porous aerogel films compared to their non‐poled solid counterparts. Then, a fully printed TENG is demonstrated using stretchable materials, exhibiting a peak power of 62.8 mW m −2 and an average power of 9.9 mW m −2 over 100 tapping cycles at 0.75 Hz. It can illuminate light‐emitting diodes (LEDs) through the harvesting of mechanical energy from human motion. This study provides a significant advance in the development of energy harvesting devices.
Förderung
- Tekniikan Edistämissäätiö
- Walter Ahlströmin Säätiö
- Academy of Finland
Zitieren
APA
Montero, K. L., Guzman, R. C., Tewari, A., Zou, H., Wang, Z. L., Mäntysalo, M., & Laurila, M. (2024). Printed and Stretchable Triboelectric Energy Harvester Based on P(VDF‐TrFE) Porous Aerogel. Advanced Functional Materials, 34(19). https://doi.org/10.1002/adfm.202312881
Vancouver
Montero KL, Guzman RC, Tewari A, Zou H, Wang ZL, Mäntysalo M, et al. Printed and Stretchable Triboelectric Energy Harvester Based on P(VDF‐TrFE) Porous Aerogel. Advanced Functional Materials. 2024;34(19). doi:10.1002/adfm.202312881
BibTeX
@article{Montero2024,
author = {Montero, Karem Lozano and Guzman, Remmi Calvo and Tewari, Amit and Zou, Haiyang and Wang, Zhong Lin and Mäntysalo, Matti and Laurila, Mika‐Matti},
title = {Printed and Stretchable Triboelectric Energy Harvester Based on P(VDF‐TrFE) Porous Aerogel},
journal = {Advanced Functional Materials},
year = {2024},
volume = {34},
number = {19},
doi = {10.1002/adfm.202312881}
}
EUVIMED