EUVIMEDEUVIMED entdecken
Crossref

Fabrication of Gradient Microstructure for Enhancing Wear Resistance of Mg‐1.9Mn‐0.3Ce Alloy via Ultrasonic Surface Rolling Process

Liangshun Huang, Meilong Feng, Yixiang Guo, Jinhui Wu, Junmao Lian, Huiming Zhang, Hai Huang, Yong Zhang

Advanced Engineering Materials · 2025-09 · 27 (18)

DOI: 10.1002/adem.202500945 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Engineering Materials, online erschienen am 10.08.2025. Verfasst von Liangshun Huang und 7 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 45 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The strengthening mechanism on wear behavior of Mg‐1.9Mn‐0.3Ce alloy subjected to surface rolling process (USRP) under different sliding speeds and applied loads is investigated in this study. The wear rates and coefficient of friction (COF) values of Mg‐1.9Mn‐0.3Ce alloy after USRP are both reduced. In particular, at a sliding speed of 0.02 m s −1 and 10 N load, the COF and wear rate of the USRP‐treated sample are ≈19% and 74% lower than those of the untreated sample. At a low sliding speed (0.02 m s −1 ), the wear behavior of untreated samples transitioned from fatigue wear to a mix of abrasive and delamination wear with increasing applied load. In contrast, the worn surface of samples treated by USRP retained fatigue wear characteristics while showing milder delamination and abrasive wear at higher applied loads. At a high sliding speed (0.2 m s −1 ), the wear resistance of Mg‐1.9Mn‐0.3Ce alloy is also improved with varying applied loads, although the wear mechanism is not significantly changed compared to the untreated sample. The improved wear behavior of Mg‐1.9Mn‐0.3Ce alloy after USRP is primarily attributed to the strengthening effect by the modified microstructure and the inhibiting effect of crack initiation and propagation enabled by the gradient microstructure.

Zitieren

APA

Huang, L., Feng, M., Guo, Y., Wu, J., Lian, J., Zhang, H., Huang, H., & Zhang, Y. (2025). Fabrication of Gradient Microstructure for Enhancing Wear Resistance of Mg‐1.9Mn‐0.3Ce Alloy via Ultrasonic Surface Rolling Process. Advanced Engineering Materials, 27(18). https://doi.org/10.1002/adem.202500945

Vancouver

Huang L, Feng M, Guo Y, Wu J, Lian J, Zhang H, et al. Fabrication of Gradient Microstructure for Enhancing Wear Resistance of Mg‐1.9Mn‐0.3Ce Alloy via Ultrasonic Surface Rolling Process. Advanced Engineering Materials. 2025;27(18). doi:10.1002/adem.202500945

BibTeX
@article{Huang2025,
  author = {Huang, Liangshun and Feng, Meilong and Guo, Yixiang and Wu, Jinhui and Lian, Junmao and Zhang, Huiming and Huang, Hai and Zhang, Yong},
  title = {Fabrication of Gradient Microstructure for Enhancing Wear Resistance of Mg‐1.9Mn‐0.3Ce Alloy via Ultrasonic Surface Rolling Process},
  journal = {Advanced Engineering Materials},
  year = {2025},
  volume = {27},
  number = {18},
  doi = {10.1002/adem.202500945}
}
Kostenlos starten →